KDF11-B и я

DEC Alpha, ARM, MIPS, PowerPC, SPARC, VAX, PDP-8 и другие устройства
Hunta
Full Member
Сообщения: 252
Зарегистрирован: 31.08.2020,21:16
Откуда: Самара

KDF11-B и я

Сообщение Hunta » 10.06.2021,07:50

Интересно, существовала ли хоть одна PDP-11/83/84/93/94 с подключённым RK11? :)

Код: Выделить всё

@173000G 
 
 
 
Testing in progress - Please wait
Memory Size is 4088 K Bytes
9 Step memory test
  Step 1 2 3 4 5 6 7 8 9
 
 
Message 04      Entering Dialog mode
 
Commands are Help, Boot, List, Setup, Map and Test.
Type a command then press the RETURN key: BOO DK7
 
 
Trying DK7
 
Starting system from DK7
 
 
RT-11SB (S) V05.07
 
.R MSCPCK
 
.SHO ALL
 
RT-11SB (S) V05.07
Booted from RK7:RT11SB
 
USR     is set SWAP
EXIT    is set SWAP
KMON    is set NOIND
MODE    is set NOSJ
TT      is set NOQUIET
ERROR   is set ERROR
SL      is set OFF
EDIT    is set KED
FORTRAN is set FORTRA
KMON nesting depth is 3
Global .SCCA flag is disabled
 
CLI is set DCL, CCL, UCL, NO UCF
 
PDP 11/83 Processor
4088KB of memory
Floating Point Accelerator Unit
Extended Instruction Set (EIS)
Memory Management Unit
Parity Memory
Cache Memory
PMI Memory
50 Hertz System Clock
 
Memory parity support
SB timer support
Global .SCCA support
FPU support
Extended unit support
 
Device    Status                   CSR     Vector(s)
------    ------                   ---     ---------
  RK      Resident                177400   220
  DL      Not installed           174400   160
  DU      Installed               172150   154
  HX      Installed               177560   000
  ZA      Installed               161014   350
  ZB      Installed               161054   354
  ZC      Installed               161114   360
  ZD      Installed               161154   364
  ZE      Not installed           161214   370
  ZF      Not installed           161254   374
  WQ      Not installed           177134   204
  WS      Not installed           177134   204
  LD      Installed               000000   000
  VM      Installed               177572   250
  MU      Not installed           174500   260
  NL      Installed               000000   000
  SL      Installed               000000   000
  EM      Installed               000000   010
 
TT  (Resident)
RK  (Resident)
    RK7 = DK , SY
HX
ZA
ZB
DU
VM
ZC
ZD
NL
LD
SL
EM
13 free slots
 
Job  Name  Console Level State    Low    High  Impure
---  ----  ------- ----- -----    ---    ----  ------
 0   RESORC   0      0   Run     000000 135334 137226
 
No multi-terminal support
 
Address   Module    Words
-------   ------    -----
160000    IOPAGE     4096.
157330    RK          148.
135400    RMON       4588.
001000    ..BG..    23680.
 
No LD units mounted
 
 
 
.COP/DEV/VER RK7: RK6:
RK6:/Copy; Are you sure? Y
 
.COP/BOO RK6:RT11XM RK6:
 
.BOO RK6:
 
RT-11XM (S) V05.07
 
.TYPE V5USER.TXT
 
                                   RT-11 V5.7
 
    Installation  of  RT-11  Version  5.7 is complete and you are now running
    RT-11 from your system volume.
 
    Your  system volume is your working volume if you have used the Automatic
    Installation (AI) procedure.  If you  have  installed  RT-11  using  that
    procedure,  Mentec  recommends  you verify the  correct operation of your
    system's software using the VERIFY verification procedure.  You can  only
    perform  VERIFY  on  the  valid target (output) media you used for the AI
    procedure.  Run VERIFY before you run CONFIG.  To run VERIFY,  enter  the
    command:
                                   IND VERIFY
 
    You should read the file V5NOTE.TXT, which you can TYPE or PRINT.  Also,
    read the Introduction to RT-11, and the Installation Guide which
    contain much of the information you need to use RT-11 Version 5.7.
 
 
.R MSCPCK
 
.SHO ALL
 
RT-11XM (S) V05.07
Booted from RK6:RT11XM
22 bit addressing is on
 
USR     is set NOSWAP
EXIT    is set SWAP
KMON    is set NOIND
RUN     is set NOVBGEXE
MODE    is set NOSJ
TT      is set NOQUIET
ERROR   is set ERROR
SL      is set OFF
EDIT    is set KEX
FORTRAN is set FORTRA
KMON nesting depth is 3
Global .SCCA flag is disabled
 
CLI is set DCL, CCL, UCL, NO UCF
 
PDP 11/83 Processor
4088KB of memory
Floating Point Accelerator Unit
Extended Instruction Set (EIS)
Memory Management Unit
Parity Memory
Cache Memory
PMI Memory
50 Hertz System Clock
 
Memory parity support
Global .SCCA support
FPU support
Extended unit support
 
Device    Status                   CSR     Vector(s)
------    ------                   ---     ---------
  RK      Resident                177400   220
  DL      Not installed           174400   160
  DU      Installed               172150   154
  HX      Installed               177560   000
  ZA      Installed               161014   350
  ZB      Installed               161054   354
  ZC      Installed               161114   360
  ZD      Installed               161154   364
  ZE      Not installed           161214   370
  ZF      Not installed           161254   374
  WQ      Not installed           177134   204
  WS      Not installed           177134   204
  LD      Installed               000000   000
  VM      Installed               177572   000
  MU      Not installed           174500   260
  NL      Installed               000000   000
  SL      Not installed           000000   000
  NQ      Not installed           174440   120
 
TT  (Resident)
RK  (Resident)
    RK6 = DK , SY
MQ  (Resident)
HX
ZA
ZB
ZC
DU
VM
ZD
LD
NL
16 free slots
 
Job  Name  Console Level State    Low    High  Impure
---  ----  ------- ----- -----    ---    ----  ------
 0   RESORC   0      0   Run     000000 105204 121616
 
No multi-terminal support
 
------- Extended Memory --------
Address   Module    Words   Type
-------   ------    -----   ----
17760000  IOPAGE     4096.   PRM    HDW    BYP
17760000  MEMTOP
00760000  VM      1966080.   SHR
00204100  ......    93152.
00161200  DU         4832.   PVT
00160000  MCA         320.   PRM
00000000  KERNEL    28672.   PRM    HDW
 
------ Low Memory -------
Address   Module    Words
-------   ------    -----
157276    RK          161.
117250    RMON       8203.
105206    USR        2577.
001000    ..BG..    17475.
 
LD0 is  ZB3:S00.DSK[1950.] #
# Handler not loaded
 
 
 
.INI RK7:
RK7:/Initialize; Are you sure? Y
Volume contains protected files; Are you sure? Y
 
.@TSYNL
 
.TIME
00:02:22
 
.COPY/DEVICE/NOQUERY SY: NL:
 
.TIME
00:02:28
 
.
Cкорость пока получилась 400 кб/с. Для сравнения - CF на DU через конвертер IDE-SCSI даёт там же 1170 кб/с, то есть к чему стремится - есть :)

Ответить